2006 TOYOTA TUNDRA

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

Tenneco Automotive (DRiV) is recalling certain aftermarket ball joints for 2004-2007 Toyota Sequoia and 2004-2006 Toyota Tundra vehicles, MOOG part number K80521, K80522, NAPA part number NCP2601633, NCP2601634, ACDelco part number 45D2344, and 45D2345. The ball joint housing may have inadequate hardness, causing premature failure.

Risk: A ball joint failure may cause a loss of control, increasing the risk of a crash.

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

AIR BAGS:SIDE/WINDOW

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2003-2006 Toyota Land Cruiser and Lexus LX470, 2005-2006 Toyota Tundra and Sequoia, 2004-2006 Toyota 4Runner and Lexus GX470 vehicles equipped with side curtain-shield-air bags. The affected vehicles have an air bag control module that may be improperly programmed, causing the side curtain-shield-air bags to deploy inadvertently.

Risk: If the side curtain-shield-air bags deploy unexpectedly, it can increase the risk of occupant injury.

SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER

Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.

Risk: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.

AIR BAGS

Toyota Motor Engineering & Manufacturing (Toyota) notified the agency on May 13, 2015, that they are recalling 2005-2007 Lexus SC, Toyota Corolla, Corolla Matrix, Sequoia, and Pontiac Vibe, and 2005-2006 Toyota Tundra vehicles that were originally sold, or ever registered, in Florida, along the Gulf Coast, Puerto Rico, Hawaii, the U.S. Virgin Islands, Guam, Saipan and American Samoa. On June 16, 2015 Toyota expanded the recall to cover an additional 769,055 vehicles, including certain model year 2002-2004 Lexus SC, Toyota Sequoia, 2003-2004 Toyota Corolla Matrix, Toyota Corolla, Pontiac Vibe, and Toyota Tundra vehicles, as well the vehicles covered by the May 13, 2015 notification in the portions of Georgia, Alabama, Louisiana, Mississippi and Texas that were not previously included. The inflators in the front passenger air bags are susceptible to rupture in the event of a crash necessitating the deployment of the front passenger air bag.

Risk: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

AIR BAGS

Toyota Motor Engineering & Manufacturing (Toyota) notified the agency on May 13, 2015 that they are recalling certain model year 2004 Sequoia vehicles manufactured August 18, 2003, to August 19, 2004, and 2003-2004 Tundra vehicles manufactured March 18, 2003, to August 25, 2004. On June 16, 2015, Toyota expanded the recall to include an additional 1,270,468 vehicles, including model year 2002-2003 and 2005-2007 Sequoia, 2005-2006 Tundra, 2003-2007 Corolla, 2003-2007 Corolla Matrix, 2003-2007 Pontiac Vibe and 2002-2007 Lexus SC vehicles. This is to address a safety defect in the passenger side frontal air bag inflator which may produce excessive internal pressure causing the inflator to rupture upon deployment of the air bag. This recall addresses both the passenger side frontal air bags that were originally installed in the vehicles, as well as replacement air bags that may have been installed as replacement service parts. A replacement air bag may have been installed, as one example, if a vehicle had been in a crash necessitating the replacement of the passenger side frontal air bag.

Risk: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER

Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.

Risk: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.

EQUIPMENT:OTHER:LABELS

GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.

Risk: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.

STRUCTURE

The contact owns a 2006 Toyota Tundra. The contact stated that upon further inspection, it was noticed that the frame was rusted. In addition, the contact related the failure to an unknown NHTSA Campaign that was performed in the past; however, the failure reoccurred. The local dealer that performed the recall repair was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 200,000.

SUSPENSION

The lower ball joint broke causing the upper ball joint to break and damage the strut rocked pion and the brake line. I contacted Toyota and they said it was fixed from a former recall

UNKNOWN OR OTHER

The frame on my 2006 Toyota Tundra SR5 has severe corrosion and multiple areas of rust perforation despite being treated under Toyota’s Limited Service Campaign D0D in 2015. During that campaign, the dealer removed the bed, documented active rust on the frame, cleaned it, and applied Corrosion-Resistant Compound (CRC) to key areas as the preventative remedy. As documented in multiple repairs the corrosion was already advancing at the time the CRC was applied, the steering shaft boot was replaced the same day as the compound was put on at 93,822 miles, several other critical safety failure shortly after; the brake pivots seized at 94900, Rotors rust pitted at 99537, bumper had perforations at 109407, 1 brake line from master cylinder and 1 brake line from ABS actuator leaking near the junction block on L/S of the frame at 113422, 52 days later the shift cable was broken at 114904. The current perforation and delamination indicate that the D0D remedy failed to prevent structural degradation as intended. The vehicle is available for inspection upon request. The vehicle’s structural integrity is severely compromised, creating a risk of frame failure while driving. This puts my safety and the safety of others at risk due to potential loss of control or component separation. The problem has not yet been inspected by the dealer in its current condition but has been escalated to Toyota Corporate. I have attached the communications with them. The truck has been fully serviced through Toyota since new, with the last documented service in January 2021. There were no warning lamps or dashboard messages prior to the failure. Visible rust first appeared prior to the D0D treatment and has now progressed to full perforation. The vehicle is currently unsafe to drive.

SUSPENSION

The frame on my 2006 Toyota Tundra SR5 has severe corrosion and multiple areas of rust perforation despite being treated under Toyota’s Limited Service Campaign D0D in 2015. During that campaign, the dealer removed the bed, documented active rust on the frame, cleaned it, and applied Corrosion-Resistant Compound (CRC) to key areas as the preventative remedy. As documented in multiple repairs the corrosion was already advancing at the time the CRC was applied, the steering shaft boot was replaced the same day as the compound was put on at 93,822 miles, several other critical safety failure shortly after; the brake pivots seized at 94900, Rotors rust pitted at 99537, bumper had perforations at 109407, 1 brake line from master cylinder and 1 brake line from ABS actuator leaking near the junction block on L/S of the frame at 113422, 52 days later the shift cable was broken at 114904. The current perforation and delamination indicate that the D0D remedy failed to prevent structural degradation as intended. The vehicle is available for inspection upon request. The vehicle’s structural integrity is severely compromised, creating a risk of frame failure while driving. This puts my safety and the safety of others at risk due to potential loss of control or component separation. The problem has not yet been inspected by the dealer in its current condition but has been escalated to Toyota Corporate. I have attached the communications with them. The truck has been fully serviced through Toyota since new, with the last documented service in January 2021. There were no warning lamps or dashboard messages prior to the failure. Visible rust first appeared prior to the D0D treatment and has now progressed to full perforation. The vehicle is currently unsafe to drive.

STRUCTURE:BODY

The frame on my 2006 Toyota Tundra SR5 has severe corrosion and multiple areas of rust perforation despite being treated under Toyota’s Limited Service Campaign D0D in 2015. During that campaign, the dealer removed the bed, documented active rust on the frame, cleaned it, and applied Corrosion-Resistant Compound (CRC) to key areas as the preventative remedy. As documented in multiple repairs the corrosion was already advancing at the time the CRC was applied, the steering shaft boot was replaced the same day as the compound was put on at 93,822 miles, several other critical safety failure shortly after; the brake pivots seized at 94900, Rotors rust pitted at 99537, bumper had perforations at 109407, 1 brake line from master cylinder and 1 brake line from ABS actuator leaking near the junction block on L/S of the frame at 113422, 52 days later the shift cable was broken at 114904. The current perforation and delamination indicate that the D0D remedy failed to prevent structural degradation as intended. The vehicle is available for inspection upon request. The vehicle’s structural integrity is severely compromised, creating a risk of frame failure while driving. This puts my safety and the safety of others at risk due to potential loss of control or component separation. The problem has not yet been inspected by the dealer in its current condition but has been escalated to Toyota Corporate. I have attached the communications with them. The truck has been fully serviced through Toyota since new, with the last documented service in January 2021. There were no warning lamps or dashboard messages prior to the failure. Visible rust first appeared prior to the D0D treatment and has now progressed to full perforation. The vehicle is currently unsafe to drive.

STRUCTURE:BODY

The contact owns a 2006 Toyota Tundra. The contact stated that while depressing the brake pedal, the steering wheel vibrated abnormally, and the steering wheel was difficult to hold steady. The contact stated that extra effort was needed to secure the steering wheel while depressing the brake pedal to stop the vehicle. The contact stated that the TPMS was providing erroneous operating information and alerts. The contact inspected the vehicle and became aware that the cross member near the steering rack had a fractured in the frame. The vehicle was taken to a Toyota Collision Center, where a mechanic determined that the entire sub frame needed to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure and referred the contact to the Toyota Collision Center for assistance. The manufacturer opened a case for the failure. The failure mileage was approximately 148,857.

UNKNOWN OR OTHER

I have a 2006 Tundra with 120k miles and I was told it wasn't one that was effected by the recall. However I'm have frame rot issues and just had to spend thousands of dollars to make it safe. This is the second time I've had to repair the frame in the 4/5 years I've owned it.

SERVICE BRAKES, HYDRAULIC

The contact owns a 2006 Toyota Tundra. The contact stated upon taking the vehicle to an independent mechanic for a routine brake line repair, the contact was informed that the sub frame was severely corroded. The mechanic informed the contact that the frame could collapse if the contact continued driving the vehicle. Additionally, the contact stated that while driving at an undisclosed speed and depressing the brake pedal, the vehicle hesitated to respond. There was no warning light illuminated. The vehicle was not repaired. No further information was available. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 35,000.

STRUCTURE

The contact owns a 2006 Toyota Tundra. The contact stated upon taking the vehicle to an independent mechanic for a routine brake line repair, the contact was informed that the sub frame was severely corroded. The mechanic informed the contact that the frame could collapse if the contact continued driving the vehicle. Additionally, the contact stated that while driving at an undisclosed speed and depressing the brake pedal, the vehicle hesitated to respond. There was no warning light illuminated. The vehicle was not repaired. No further information was available. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 35,000.

SERVICE BRAKES

My 2006 tundra has major rust on the frame to the point it isn't safe to drive anymore. I have reached out to Toyota and my local dealer and have received the same answer from both saying its not something that Toyota will cover, despite the fact that there was a national safety recall that started in 2016 for rust related issues.

STRUCTURE:BODY

My 2006 tundra has major rust on the frame to the point it isn't safe to drive anymore. I have reached out to Toyota and my local dealer and have received the same answer from both saying its not something that Toyota will cover, despite the fact that there was a national safety recall that started in 2016 for rust related issues.