2009 SCION XD

VISIBILITY:POWER WINDOW DEVICES AND CONTROLS

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Risk: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

SEATS

Toyota is recalling certain model year 2006-2010 Yaris vehicles manufactured August 22, 2005, through May 12, 2010, and 2008-2010 Scion xD vehicles manufactured April 4, 2007, through May 12, 2010. In the affected vehicles, the springs used for the seat rails on the driver's seat and the seat rails of the front passenger seat of three-door models may break.

Risk: If the spring breaks, the seat may not lock in position. In the event of a vehicle crash, the seat could move increasing the risk of injury to the seat occupant.

VISIBILITY:POWER WINDOW DEVICES AND CONTROLS

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

Risk: If the switch overheats, it may melt, possibly resulting in a fire.

EQUIPMENT:OTHER:LABELS

GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.

Risk: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.

UNKNOWN OR OTHER

Drove car and heard loud noise issuing from the passenger side rear. Upon viewing the wheel was angled in at the top. After removing the wheel I found the rear crossmember subframe axle had a complete break in the weld holding the angle from the straight part of the beam to the wheel and suspension plate. After going online to see if similar issues happen on the same side of the vehicle, I found many reports of weld failures on the same side at the same joint. This is an EXTREMELY dangerous weld failure--if it had happened during highway travel the potential for catastrophic injury or death is high, in my opinion. Please investigate other reports to the NTSB about this make and model, and please search model years on or about 2007-2012 as other scion owners have had the same issue. This is a one owner car, we purchased it new in 2009. The opposite weld is also showing signs of stress, but not broken or cracked.

WHEELS

Drove car and heard loud noise issuing from the passenger side rear. Upon viewing the wheel was angled in at the top. After removing the wheel I found the rear crossmember subframe axle had a complete break in the weld holding the angle from the straight part of the beam to the wheel and suspension plate. After going online to see if similar issues happen on the same side of the vehicle, I found many reports of weld failures on the same side at the same joint. This is an EXTREMELY dangerous weld failure--if it had happened during highway travel the potential for catastrophic injury or death is high, in my opinion. Please investigate other reports to the NTSB about this make and model, and please search model years on or about 2007-2012 as other scion owners have had the same issue. This is a one owner car, we purchased it new in 2009. The opposite weld is also showing signs of stress, but not broken or cracked.