2011 MINI COOPER S

ELECTRICAL SYSTEM

BMW of North America, LLC (BMW) is recalling certain 2008-2014 MINI Clubman Cooper, Clubman Cooper S, Clubman John Cooper Works, and 2007-2013 MINI Hardtop 2-Door Cooper, Cooper S, and John Cooper Works vehicles sold, or ever registered, in Alaska, Colorado, Connecticut, Delaware, Illinois, Indiana, Iowa, Kansas, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Hampshire, New Jersey, New York, North Dakota, Ohio, Pennsylvania, Rhode Island, South Dakota, Utah, Vermont, Virginia, West Virginia, Washington D.C., and Wisconsin. The electronic control module in the driver's side footwell area may short-circuit, due to corrosion from water and road salt.

Risk: An electrical short-circuit can increase the risk of a fire.

ENGINE AND ENGINE COOLING:ENGINE

BMW of North America, LLC (BMW) is recalling certain 2011-2012 BMW 550i, 550i xDrive, 550i Gran Turismo, 550i Gran Turismo xDrive, 750i, 750Li, 750i xDrive, 750Li xDrive, 760Li, X5 xDrive50i, X5 M, X6 xDrive50i, X6 M, ActiveHybrid7, MINI Cooper S Convertible, John Cooper Works (JCW) Convertible, Cooper S Countryman, Cooper S Countryman ALL4, Cooper S, JCW, Cooper S Clubman, JCW Clubman, Cooper S Roadster, JCW Roadster, Cooper S Coupe, JCW Coupe and Rolls-Royce Ghost, 2011 BMW X6 Hybrid and 2012 BMW 650i Coupe, 650i xDrive Coupe, 650i Convertible and 650i xDrive Convertible vehicles. The electric auxiliary water pump may fail and cause the circuit board to overheat.

Risk: If the circuit board were to overheat, it can increase the risk of a fire.

UNKNOWN OR OTHER

Failure of the Footwell Module failed due to corrosion by water intrusion as diagnosed by Mini Dealership. Windows, Turn signals and lights were inoperable as a result of failure. This matched the situation outlined in your recall notice Part 573 Safety Recall Report 23V-337. Car matched the model/years affected/listed in recall. However, Mini Dealer informed me my VIN was not listed in their recall. Subsequent research indicated that NHTSA/Mini limited the recall to cars purchased cars sold or registered in specific states (not part of the Safety recall report). Ref NEF-107DM dated 5/19/2023. I drove car in those states but did not buy or register the vehicle in them. I encourage you to have Mini extend it's recall/warranty to all vehicles which exhibit the safety failure.

EXTERIOR LIGHTING

Failure of the Footwell Module failed due to corrosion by water intrusion as diagnosed by Mini Dealership. Windows, Turn signals and lights were inoperable as a result of failure. This matched the situation outlined in your recall notice Part 573 Safety Recall Report 23V-337. Car matched the model/years affected/listed in recall. However, Mini Dealer informed me my VIN was not listed in their recall. Subsequent research indicated that NHTSA/Mini limited the recall to cars purchased cars sold or registered in specific states (not part of the Safety recall report). Ref NEF-107DM dated 5/19/2023. I drove car in those states but did not buy or register the vehicle in them. I encourage you to have Mini extend it's recall/warranty to all vehicles which exhibit the safety failure.

ELECTRICAL SYSTEM

Failure of the Footwell Module failed due to corrosion by water intrusion as diagnosed by Mini Dealership. Windows, Turn signals and lights were inoperable as a result of failure. This matched the situation outlined in your recall notice Part 573 Safety Recall Report 23V-337. Car matched the model/years affected/listed in recall. However, Mini Dealer informed me my VIN was not listed in their recall. Subsequent research indicated that NHTSA/Mini limited the recall to cars purchased cars sold or registered in specific states (not part of the Safety recall report). Ref NEF-107DM dated 5/19/2023. I drove car in those states but did not buy or register the vehicle in them. I encourage you to have Mini extend it's recall/warranty to all vehicles which exhibit the safety failure.

ELECTRICAL SYSTEM

The contact owns a 2011 Mini Cooper S. The contact recently replaced the 12-Volt battery; however, while attempting to roll down the windows, the windows failed to respond as needed. The contact stated that the running lights and fog lights were inoperable. The contact stated that the battery was replaced at a tire and battery shop. The contact drove the vehicle back to the shop and was informed that the vehicle could not be repaired. The contact had researched online and related the vehicle failure to NHTSA Campaign Number: 23V337000 (Electrical System). The contact called the manufacturer and was informed that the VIN was not included in the recall. The contact was referred by the manufacturer to contact the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 77,800.

UNKNOWN OR OTHER

My mini after the shop installed a new battery, the power windows don't work( can not roll up or down) as well as the lightning. I saw there is a recall for the footwell module for model 2007-2014 but when I call Mini, the agent told me that my car is not covered. This is a very expensive and important part to replace so please help me the best that you can. Thanks

ELECTRICAL SYSTEM

My mini after the shop installed a new battery, the power windows don't work( can not roll up or down) as well as the lightning. I saw there is a recall for the footwell module for model 2007-2014 but when I call Mini, the agent told me that my car is not covered. This is a very expensive and important part to replace so please help me the best that you can. Thanks

ENGINE

Car stalls while driving and will not start again. No codes thrown. Found relay K96 on Junction Box Electronics module to have cracked through-hole solder joints resulting in bad continuity. Relay K96 supplies power to the low pressure fuel pump in the tank, thus with bad continuity, the pump gets no power. Relay K96 P/N is NEC Philippines P/N EP2F-B3G1ST. This issue has happened to many other people with the same car that I know. I suspect heat cycles over time stressed and fatigued the solder joints, causing the joint to crack. Overall the circuit board layout needs a heat sink for the relay to alleviate the heat produced from operation. I am IPC certified and work with aircraft engine electronics regularly and have seen similar issues.