2014 BMW 428I

ENGINE AND ENGINE COOLING:COOLING SYSTEM:PUMP

BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.

Risk: An electrical short increases the risk of a fire.

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.

AIR BAGS:SIDE/WINDOW

BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.

Risk: An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.

FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP

BMW of North America LLC (BMW) is recalling certain model year 2014 228i Coupe, M235i Coupe, 320i, 320xi, 328i, 328xi, 335i, 335xi, ActiveHybrid 3, 328xi Sports Wagon, 428i Coupe, 428xi Coupe, 435i Coupe, 435xi Coupe, 428i Convertible, 428xi Convertible, 435i Convertible, 328xi Gran Turismo, 335xi Gran Turismo, and 2015 428i Gran Coupe, 428xi Gran Coupe, and 435i Gran Coupe vehicles. Improper nickel plating of components within the fuel pump may result in the fuel pump failing.

Risk: If the fuel pump fails, the vehicle may stall without warning, increasing the risk of a crash.

ENGINE

I have tried reaching BMW USA 3-4 times since November 2024 until now. The representative said BMW is working on correcting the problem. I have CC the email that was sent this June 2025 with no replies. 1 year has passed since the recall was issued and BMW USA has not created a remedy/fix for the coolant problem. I had this car on the TURO car rental platform as I am a host on TURO. I can't list this car to rent out because of the recall. Turo will not allow owners of recalled cars to list their cars because the car could be "potentially unsafe." Yet, the "owner" is driving these "unsafe"' cars on the road. I did my part. I already sent another recent email to get a solution. What would be my next step? (Almost one year now....) Also, I am sending this email Pacific time at 5:07 WED., July 30th. On the document: the Update IS on THURSDAY JULY 31st. WHAT???!!!!! Make it make sense . Frustrated OWNER

FUEL/PROPULSION SYSTEM

the recall was dated 12 August 2024. To date BMW North America has not provided the parts needed to effect the repair. it has been 10 months since the recall. BMW NA is dragging its feet. it is time something is done to require BMW NA to fix the problem,

ELECTRICAL SYSTEM

the recall was dated 12 August 2024. To date BMW North America has not provided the parts needed to effect the repair. it has been 10 months since the recall. BMW NA is dragging its feet. it is time something is done to require BMW NA to fix the problem,

ENGINE

the recall was dated 12 August 2024. To date BMW North America has not provided the parts needed to effect the repair. it has been 10 months since the recall. BMW NA is dragging its feet. it is time something is done to require BMW NA to fix the problem,

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

UNKNOWN OR OTHER

The manufacturer has failed or is unable to remedy this safety recall for my vehicle in a timely manner. Issue: 1 open recall since Aug 13, 2024 for: ENGINE COOLANT PUMP: The electrical connector of the engine coolant pump could become damaged. Small drops of liquid from the positive crankcase ventilation (PCV) system could drip down onto the electrical connector of the pump.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact stated that while driving approximately 65 - 70 MPH and attempting to change lanes, the vehicle lost power steering functionality. The message “Chassis Unstable” was displayed on the instrument panel. The contact used excessive force to steer the vehicle to pull over to the side of the road to inspect the vehicle. The contact was unable to find the cause of failure and continued to drive the vehicle without power steering functionality. The message of an excessive power drain for the battery was displayed. The vehicle was unable to switch to different settings, such as Sport 1, Sport 2, and Eco Pro due to the drive setting remaining stuck in Comfort Mode. The cruise control failed intermittently. While driving approximately 65 -70 MPH, the contact noticed a burning plastic odor coming from the front-end of the vehicle into the cabin. After arriving at the destination and inspecting underneath the hood of the vehicle, the contact noticed that the terminal door for the jumper cables and the housing were smoking. Additionally, there were burned areas surrounding the battery. The vehicle was taken to the dealer, who diagnosed that the electronic control module had failed and needed to be replaced. The vehicle was not repaired. The contact became aware of NHTSA Campaign Number: 16V704000 (Steering); however, the VIN was not included. The manufacturer was informed of the failure. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 80,000.

STEERING

The contact owns a 2014 BMW 428I. The contact stated that while driving approximately 65 - 70 MPH and attempting to change lanes, the vehicle lost power steering functionality. The message “Chassis Unstable” was displayed on the instrument panel. The contact used excessive force to steer the vehicle to pull over to the side of the road to inspect the vehicle. The contact was unable to find the cause of failure and continued to drive the vehicle without power steering functionality. The message of an excessive power drain for the battery was displayed. The vehicle was unable to switch to different settings, such as Sport 1, Sport 2, and Eco Pro due to the drive setting remaining stuck in Comfort Mode. The cruise control failed intermittently. While driving approximately 65 -70 MPH, the contact noticed a burning plastic odor coming from the front-end of the vehicle into the cabin. After arriving at the destination and inspecting underneath the hood of the vehicle, the contact noticed that the terminal door for the jumper cables and the housing were smoking. Additionally, there were burned areas surrounding the battery. The vehicle was taken to the dealer, who diagnosed that the electronic control module had failed and needed to be replaced. The vehicle was not repaired. The contact became aware of NHTSA Campaign Number: 16V704000 (Steering); however, the VIN was not included. The manufacturer was informed of the failure. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 80,000.

FUEL/PROPULSION SYSTEM

Car shut down and is believed to be a lemon car, and continuously leaks in spite being serviced on numerous occasions.

ENGINE

Car shut down and is believed to be a lemon car, and continuously leaks in spite being serviced on numerous occasions.

ELECTRICAL SYSTEM

Car shut down and is believed to be a lemon car, and continuously leaks in spite being serviced on numerous occasions.

ENGINE

The contact owns a 2014 BMW 428I. The contact stated that the vehicle was experiencing a significant oil leak. The contact stated that upon parking the vehicle, the contact noticed that a significant amount of oil was leaking onto the ground. The vehicle was taken to Crescent Automotive, where it was purchased. The vehicle was then taken to C&C Automotive, where a synthetic oil change was performed. The vehicle was taken to an independent mechanic, where the filter, the drain plug, the drain plug gasket, and the air filter were replaced; however, the failure recurred. The vehicle was taken to a local Pep Boys, where the oil leak was evaluated, but the vehicle was not repaired. The vehicle was taken to a BMW dealer, where an unknown service was performed; however, the failure persisted. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 99,099.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that while idling in traffic on the highway, the temperature gauge indicated that the engine was running extremely hot. The message "Engine Over temperature - Stop Carefully" was displayed. The contact pulled over onto the shoulder lane, turned off the vehicle, and waited for the engine to cool down. The vehicle was restarted and driven toits destination after the engine had cooled down. The approximate failure mileage was 80,000. VIN tool confirms parts not available.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that while idling in traffic on the highway, the temperature gauge indicated that the engine was running extremely hot. The message "Engine Over temperature - Stop Carefully" was displayed. The contact pulled over onto the shoulder lane, turned off the vehicle, and waited for the engine to cool down. The vehicle was restarted and driven toits destination after the engine had cooled down. The approximate failure mileage was 80,000. VIN tool confirms parts not available.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact stated while driving at an undisclosed speed, there was a burning odor inside the vehicle. The vehicle was not diagnosed or repaired by an independent mechanic. The dealer was made aware of the failure. The contact was advised not to drive the vehicle. Additionally, the contact had been without a vehicle for more than four months. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was 69,700. VIN tool confirms parts not available.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact stated while driving at an undisclosed speed, there was a burning odor inside the vehicle. The vehicle was not diagnosed or repaired by an independent mechanic. The dealer was made aware of the failure. The contact was advised not to drive the vehicle. Additionally, the contact had been without a vehicle for more than four months. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was 69,700. VIN tool confirms parts not available.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING

I was entering the freeway as I was merging from the on-ramp onto the freeway after it had rained that day the car began to spun out of control as I was trying to regain the vehicle it'slammed into the side rail bouncing off of it and then I stepped on the brakes but the car proceeded to go forward hit the rail again which caused the damage to the front bumper, hood, fenders, lighting system, and some frame work.

FUEL/PROPULSION SYSTEM

I was entering the freeway as I was merging from the on-ramp onto the freeway after it had rained that day the car began to spun out of control as I was trying to regain the vehicle it'slammed into the side rail bouncing off of it and then I stepped on the brakes but the car proceeded to go forward hit the rail again which caused the damage to the front bumper, hood, fenders, lighting system, and some frame work.

SERVICE BRAKES

I was entering the freeway as I was merging from the on-ramp onto the freeway after it had rained that day the car began to spun out of control as I was trying to regain the vehicle it'slammed into the side rail bouncing off of it and then I stepped on the brakes but the car proceeded to go forward hit the rail again which caused the damage to the front bumper, hood, fenders, lighting system, and some frame work.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ENGINE AND ENGINE COOLING

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

ELECTRICAL SYSTEM

The contact owns a 2014 BMW 428I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The contact stated that while driving at various speeds, the contact noticed an abnormal burning odor inside the cabin of the vehicle. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was unknown. VIN tool confirms parts not available.