2018 ALTEC AERIAL DEVICE

ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES

Altec Industries, Inc. (Altec) is recalling certain 2004-2023 AT Series aerial devices. The cables in the engine compartment may contact the vehicle's hood, damaging the cables and causing a short circuit.

Risk: A short circuit increases the risk of a fire.

STRUCTURE:BODY

Altec Industries, Inc. (Altec) is recalling certain 2016-2022 DM, DH, DC, DL, D2000, D3000, and D4000 series digger derricks, and AM55 aerial devices. The base of the rear pole rack may be missing a weld.

Risk: A missing weld on the rear pole rack can lead to a crack that could cause the pole and rack to drop in height, increasing the risk of an injury.

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER

Altec Industries, Inc. (Altec) is recalling certain 2018-2021 DC and DM Series Digger Derricks and AM series Aerial Devices. The unit subbase may develop cracks in the bulkhead plate, which can cause the shear plates to fail.

Risk: Shear plate failure can result in the separation of the subbase and truck frame, increasing the risk of injury.

EQUIPMENT

Altec Industries, Inc. (Altec) is recalling certain 2017-2021 SK185-MP, and SKC landscaping spray vans. The vehicles are not equipped with carbon monoxide detectors.

Risk: Elevated levels of carbon monoxide gas may not be detected, increasing the risk of injury.

ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS

Altec Industries, Inc. (Altec) is recalling certain 2017-2021 Altec AT200A, AT235, AT235P, AT237, AT37G, AT40G, AT41M, and CB5-132D-S aerial devices. A wire to the boom stow sensor may be routed over a sharp edge, which can expose the wire to metal and result in a blown ignition circuit fuse.

Risk: A blown fuse can cause an engine stall, increasing the risk of a crash.

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:TURNTABLE

Altec Industries, Inc. (Altec) is recalling certain 2017-2021 LS60 aerial devices. The outer-race rotation bearing bolt washers may interfere with an adjacent pedestal weld, which could cause the rotation bearing bolts to break.

Risk: Broken bolts can cause the pedestal to separate from the turntable, increasing the risk of injury.

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER

Altec Industries, Inc. (Altec) is recalling certain 2016-2020 DH-B Series, DH-E Series, and D3000-E digger derricks set up for combined use and equipped with radio remote upper controls. These units only have the derrick use capacity chart and do not have the combined use capacity chart.

Risk: The operator may not have access to the rated capacity information while they are operating the equipment in combined use, increasing the risk of an injury.

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:MOTOR/HYDRAULIC PUMP

Altec Industries, Inc. (Altec) is recalling certain 2017-2021 AN67-E100, AA67-E100, AN67, AA67, and AN55-E88 aerial devices. The hydraulic plumbing to the lift cylinders of the lower and upper booms could be connected incorrectly, allowing the boom to overextend.

Risk: The operator could overextend the boom while using the material handling jib, causing the aerial device to tip over and increasing the risk of injury.

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:TURNTABLE

Altec Industries, Inc. (Altec) is recalling certain 2016-2021 LS87 aerial devices. The outer-race rotation bearing bolt washers may interfere with an adjacent pedestal weld, which could cause the rotation bearing bolts to break.

Risk: Broken bolts can cause the pedestal to separate from the turntable, increasing the risk of injury.

EQUIPMENT

Altec Industries, Inc. (Altec) is recalling certain 2005-2021 A65, A70, A75, A72-T, A77-T, and A82-T vehicles. The lower and upper boom raise spools can shift after releasing the joystick or control interlock.

Risk: Unintended movement of the lower and upper booms increases the risk of injury.

STRUCTURE:CRITICAL FASTENERS

Altec Industries, Inc. (Altec) is recalling certain 2017-2018 AT37/41/48M, AT41P, AT48S, L37M, L42A, and TA40 aerial device vehicles. The rotation bearing fasteners may experience stress corrosion cracking.

Risk: Cracked rotation bearing fasteners may break, causing separation of the pedestal and turntable, increasing the risk of death and/or injury.

TRAILER HITCHES

Altec Industries Inc. (Altec) is recalling certain 2014-2020 Aerial Devices and body only units equipped with Class 3 towing hitches. The tow hitch may have incorrect load rating markings, and may have been damaged by unintentional overloading.

Risk: If the tow hitch is overloaded, the hitch may fail, increasing the risk of a crash.

ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL

Altec Industries Inc. is recalling certain 2015-2018 LR7, ALB, AC18, AC23, and AC38 vehicles built on an International N9/N10 chassis. During an HC Desorb cycle, the vehicle's idle will rapidly rise causing an increase in pump flow. The increased pump flow can result in the moving speed of the boom changing.

Risk: The change in boom speed can result in unintended positioning of the boom, increasing the risk of injury.

EQUIPMENT

Altec Industries Inc. (Altec) is recalling certain 2018-2020 AA55, AM50 and A77 Aerial Devices and D2, D3, D4, DH-B and DH-H Digger Derricks. The bolts that secure the pedestal to the turntable (with head marking 5185) may fail.

Risk: If the fasteners break, the pedestal may separate from turntable, increasing the risk of injury or death.

ENGINE AND ENGINE COOLING:EXHAUST SYSTEM

Altec Industries, Inc. (Altec) is recalling certain 2017-2020 AT200A, AT235, AT37-G, AT40-G, AT41/48M Aerial Devices mounted on a Ford F-350, F-450 or F-550 chassis equipped with a gas engine and Chelsea 249 Power Take-Off (PTO). The PTO may leak oil onto the exhaust heat shield thermal blanket.

Risk: Oil absorbed by the exhaust heat shield thermal blanket has an increased risk of a fire from being exposed to hot engine components.

EQUIPMENT

Altec Industries, Inc. (Altec) is recalling certain 2018-2020 AA, AM, AN, A-Class, TA, DM, DL, DXXXX, DC, and DT digger derricks and aerial device vehicles equipped with a DC pump. A hydraulic check valve can have a snap ring failure resulting in the snap ring becoming lodged in a counterbalance or control valve allowing continued movement.

Risk: Unintended boom movement may result in potential injury and or property damage.

EQUIPMENT

Altec Industries Inc. (Altec) is recalling certain 2017-2018 LR7, TA50/55/60 and L42/45 Aerial Devices. Multiple fasteners used to secure the rotation bearing may break, possibly resulting in the pedestal separating from the turntable.

Risk: If the pedestal separates from the turntable, it can increase the risk of injury or death.

EQUIPMENT

Altec Industries Inc. (Altec) is recalling certain 2016-2019 LR7 Series Aerial Devices. The aerial device can be operated without the rear outriggers being deployed, which may cause the unit to be unstable.

Risk: An unstable aerial device may suddenly collapse, increasing the risk of injury.

EQUIPMENT

Altec Industries Inc. (Altec) is recalling certain 2018-2019 AT200A, AT235, AT235P, AT37-G, AT40-G and AT248F Aerial Devices. The aerial devices have not been stability tested in accordance with ANSI A92.2.

Risk: An unstable aerial device may suddenly collapse, increasing the risk of injury or death.

EQUIPMENT:MECHANICAL:WINCH

Altec Industries Inc. (Altec) is recalling certain 2012-2019 Altec AM60E, AA55E, AH75/85/100, AH125, and AH150 Aerial Devices. The recovery winch valve may allow the winch to lift more than it is rated for.

Risk: If the recovery winch attempts to lift more than it is rated for, it can increase the risk of an injury or death.

EQUIPMENT

Altec Industries Inc. (Altec) is recalling certain 2017-2019 LS60 Aerial Devices. The aerial devices may not meet all aerial level ground and slope stability requirements, allowing the units to become unstable and possibly overturn.

Risk: An unstable aerial device can increase the risk of injury.

EQUIPMENT:MECHANICAL

Altec Industries Inc. (Altec) is recalling certain 2017-2018 Altec LR7, TA50, TA55, TA60, and TA45M-T50 Aerial Devices. The fasteners that are used to secure the turntable to the pedestal may fail.

Risk: If multiple fasteners fail, the pedestal and turntable may separate, increasing the risk of death or injury.

EQUIPMENT

Altec Industries Inc. (Altec) is recalling certain 2018-2019 AT37/41/48 and L37/42/44 Aerial Devices. The high strength fasteners used to secure the pedestal to the turntable may fail.

Risk: If the fasteners fail, the pedestal may separate from the turntable, increasing the risk of injury or death.

STRUCTURE

Altec Industries Inc. (Altec) is recalling certain 2018-2019 LR7, TA50, TA55, TA60 and TDA58 Aerial Devices. The high strength fasteners used to secure the pedestal to the turntable may fail.

Risk: If the fasteners break, the pedestal may separate from turntable, increasing the risk of injury or death.

SERVICE BRAKES, AIR

Altec Industries Inc. (Altec) is recalling certain 2003-2019 Altec TA45, TA50, TA55, TA60, L37, L39, LRV, LR7, A-T40C, T40P and AP45 vehicles equipped with air-cushioned pintle hitch and/or accessory air components. The accessories utilizing chassis air supply may be missing pressure protection valves. The accessory lines may not prevent service brake line pressure loss due to failure or leakage in the accessory air system. Additionally, the air cushioned pintle hook may have been connected to the incorrect air lines. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

Risk: Loss of service brake pressure can increase the risk of a crash.

STRUCTURE

Altec Industries Inc. (Altec) is recalling certain 2017-2018 Altec LR7, L42A and AT37-G TDA58 aerial devices and DB37, DL/DMB D2/3/4B, and DMB digger derricks, equipped with fiberglass platforms. The step on the outside of the fiberglass platform can break off during normal use.

Risk: If the step separates from the platform, it can increase the risk of injury.

EXTERIOR LIGHTING:BRAKE LIGHTS

Altec Industries, Inc is recalling certain 2017-2018 Digger Derrick, Aerial Devices, and Service Body vehicles, equipped with Whelen accessory brake lights. Depending on the specific wiring of the vehicle, these brake lights may illuminate when the brake pedal has not been pressed. As such these vehicles fail to comply to with the requirements of Federal Motor Vehicle Safety Standard FMVSS 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: If the brake lights incorrectly illuminate, it can confuse other drivers, possibly increasing the risk of a crash.

STRUCTURE

Altec Industries Inc. (Altec) is recalling certain 2018 Altec AC18, AC23, AC30, AC40, AC45 Cranes, D2045, DT65 Digger Derricks, and AA55 Aerial Devices. The rotation platform fasteners may have been overtightened, possibly resulting in the fasteners breaking.

Risk: If the fasteners break, the pedestal or turntable may separate from the vehicle, increasing the risk of injury.

ELECTRICAL SYSTEM:12V/24V/48V BATTERY

Altec Industries Inc. (Altec) is recalling certain 2017-2018 Altec LS63 Aerial Devices. The fuse for the battery was not installed to the guidelines. The incorrectly placed fuse may increase the risk for an electrical short.

Risk: An electrical short can increase the risk of a fire.

TRAILER HITCHES

Altec Industries Inc. (Altec) is recalling certain 2012-2018 Altec LS63 and LS87 aerial devices equipped with a pintle hook mounted into the Class 3 receiver tube. This towing combination was shipped without a placard that provides the maximum allowable towing limit, possibly resulting in the receiver tube being overloaded.

Risk: An overloaded receiver tube could detach, increasing the risk of a crash.

ELECTRICAL SYSTEM:WIRING

Altec Industries Inc. (Altec) is recalling certain 2017-2018 AT37-G, AT40, AT37, AT41, AT48 and L37M Aerial Devices. The under-hood wiring on these vehicles may be damaged by sharp edges within the engine bay area.

Risk: Damaged wiring can increase the risk of a fire.

STRUCTURE

Altec Industries, Inc. (Altec) is recalling certain 2018 Altec DM45, DM47B, DC45 and DC47 Digger Derricks and TA50 and TA60 Aerial Devices. The high strength fasteners used to secure the pedestal to the turn table may fail.

Risk: If the fasteners fail, the pedestal may separate from the turn table, increasing the risk of injury.